View RE46C120_734513.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

R&E International
RE46C120
CMOS Ionization Smoke Detector ASIC Product Specification
General Description
The RE46C120 is low power CMOS ionization type smoke detector IC. With a few external components this circuit will provide all the required features for an ionization type smoke detector. An internal oscillator strobes power to the smoke detection circuitry for 10.5mS every 1.66 seconds to keep standby current to a minimum. A check for a low battery condition is performed every 40 seconds when in standby. The Tone input allows for selection of a temporal pattern or a 2/3 duty cycle continuous tone. The temporal horn pattern supports the NFPA 72 emergency evacuation signal. Although this device was designed for smoke detection utilizing an ionization chamber it could be used in a variety of security applications. Utilizing low power CMOS technology the RE46C120 was designed for use in smoke detectors that comply with Underwriters Laboratory Specification UL217 and UL268.
Features
* * * * * * * * * * Guard Outputs for Ion Detector Input +/-0.75pA Detect Input Current Internal Reverse Battery Protection Internal Low Battery Detection Pin Selectable Horn Pattern Low Quiescent Current Consumption (<6.5uA) Available in 16L PDIP or 16L N SOIC ESD Protection on all Pins Compatible with MC145017, MC14467 Available in Standard Packaging or RoHS Complaint Pb Free Packaging
Pin Configuration
DETCOMP N/C LBADJ TONE LED VDD RBIAS FEED
1 2 3 4 5 6 7 8
16 15 14 13 12 11 10 9
GUARD2 DETECT GUARD1 VSEN OSCAP HS HB VSS
ABSOLUTE MAXIMUM RATINGS
PARAMETER Supply Voltage Input Voltage Range Except FEED FEED Input Voltage Range Reverse Battery Time Input Current except FEED Operating Temperature Storage Temperature Maximum Junction Temperature SYMBOL VDD Vin Vinfd TRB Iin TA TSTG TJ VALUE 15 -.3 to Vdd +.3 -10 to +22 5 10 -10 to 60 -55 to 125 150 UNITS V V V S MA C C C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only and operation at these conditions for extended periods may affect device reliability. This product utilizes CMOS technology with static protection; however proper ESD prevention procedures should be used when handling this product. Damage can occur when exposed to extremely high static electrical charge
Telephone 610.992.0727 Page 1 of 7 E-mail: rande@randeint.com DS-RE46C120-010907 This datasheet contains PROPRIETARY and CONFIDENTIAL information. Facsimile 610.992.0734
RE46C120
CMOS Ionization Smoke Detector ASIC Product Specification R&E International
DC Electrical Characteristics at TA = 25C, VDD=9V, VSS=0V (unless otherwise noted) Test Pin
6 6 6 4,8 4,8 15 15 4 8 15 15 8 5 10,11 1 10,11 1 5 6 13 3 14,15 15,16 13,15 14,15 13,15 14,16 13
Guard Amplifier Guard Amplifier Smoke Comparator Guard Amplifier, Note 2 Smoke Comparator, Note 2 Guard Amplifier Outputs, Note 2 No Alarm to Alarm Condition VDD=9V, DETECT=VSS, 0-40% RH VDD=9V, DETECT=VSS, 85% RH Note 1 TONE=VSS, RBIAS=8.2M, FEED=-10V VDD=9V, DETECT=VDD, 0-40% RH VDD=9V, DETECT=VDD, 85% RH Note 1 FEED=22V LED Off IOH=-16mA, VDD=7.2V IOH=-30ua IOL=16mA, VDD=7.2V IOL=30ua IOL=10mA, VDD=7.2V TA=-10 to 60C, Note 3
Parameter
Supply Voltage Supply Current
Symbol
VDD IDD1 IDD2 VIH VIL ILDET1 ILDET2 ILTONE ILFD
Test Conditions
Operating RBIAS=8.2M, OSCAP=.1uF RBIAS=8.2M, OSCAP=.1uF;Vdd=12V
Min
6
Limits Typ Max
12 4.5 6.5 9
Units
V uA uA V V pA pA nA uA pA pA uA uA V V
Input Voltage High Input Voltage Low Input Leakage Low
6.2
4.5 4.5 2.7 -0.75 -1.50
-100
-450 -50 0.75 1.50 50 1
Input Leakage High
IHDET1 IHDET2 IHFD
Output Off Leakage High Output Voltage High
IOHZ VOH1 VOH2 VOL1 VOL2 VOL3
6.3 8.5 .9 .5 3 7.2 47 -50 -50 -50 2 .5 10 90 130 170 7.5 50 65.5 50 50 50 VDD-.5 VDD-2 7.8 53
Output Voltage Low
V V V V %VDD %VDD mV mV mV V V k mV
Low Battery Voltage Internal Sensitivity Set Voltage
VLB VSET1 VSET2 VGOS1 VGOS2 VGOS3
Offset Voltage
Common Mode Voltage
VCM1 VCM2 ZOUT VHYS
Output Impedance Hysteresis
Note 1: Sample test only Note 2: Not 100% production tested Note 3: Production test at room with temperature guardbanded limits.
Telephone 610.992.0727 Page 2 of 7
E-mail: rande@randeint.com DS-RE46C120-010907 This datasheet contains PROPRIETARY and CONFIDENTIAL information.
Facsimile 610.992.0734
RE46C120
CMOS Ionization Smoke Detector ASIC Product Specification R&E International
AC Electrical Characteristics at TA = 25C, VDD=9V, OSCAP=.1uF, RBIAS=8.2M, VSS=0V (unless otherwise noted) Test Pin
12 12 5 5 5 5 10,11 10,11 10,11 10,11 10,11 10,11 10,11
Parameter
Oscillator Period
Symbol
TPER1 TPER2 TPW TLON TLOF1 TLOF2 THON1 THON2 THON3
Test Conditions
No Alarm Condition Alarm Condition Operating Operating Standby, No Alarm Alarm Condition Operating, Alarm Condition, Note 4, TONE=VDD or Float Low Battery, No Alarm Operating, Alarm Condition, TONE=Low Operating, Alarm Condition, Note 4, TONE=VDD or Float Operating, Alarm Condition, Note 4, TONE=VDD or Float Operating, Alarm Condition, TONE=Low Low Battery, No Alarm
Min
1.34 37.5 9.1 9.1 32 .9 450 9.1 150 450 1.35 75 32
Limits Typ Max
1.67 41.5 10.5 10.5 40 1 500 10.5 166 500 1.5 83 40 2 45.8 12.9 12.9 48 1.1 550 12.9 183 550 1.65 92 48
Units
S mS mS mS S S mS mS mS mS S mS S
Oscillator Pulse Width LED On Time LED Off Time
Horn On Time
Horn Off Time
THOF1 THOF2 THOF3 THOF4
Note 4 : See timing diagram for Horn Temporal Pattern
Functional Block Diagram
Figure 1
Telephone 610.992.0727 Page 3 of 7
E-mail: rande@randeint.com DS-RE46C120-010907 This datasheet contains PROPRIETARY and CONFIDENTIAL information.
Facsimile 610.992.0734
RE46C120
CMOS Ionization Smoke Detector ASIC Product Specification R&E International
DEVICE DESCRIPTION and APPLICATION NOTES
Note: All timing references are nominal values. Refer to the electrical specifications for limits Internal Timing - With external components as indicated on the application drawing the period of the oscillator is 1.67 seconds in standby. Every 1.66 seconds the detection circuitry is powered up for 10.5mS and the status of the smoke comparator is latched. In addition every 40 seconds the LED driver is turned on for 10.5mS and the status of the low battery comparator is latched. The smoke comparator status is not checked during the low battery test, during the low battery horn warning chirp, or when the horn is on due to an alarm condition. If an alarm condition is detected the oscillator period increases to 41.5mS. Due to the low currents used in the oscillator the capacitor on pin 12 should be a low leakage type. Oscillator accuracy will depend mainly on the tolerance of the RBIAS resistor and OSCAP capacitor. Smoke Detection Circuit - The smoke comparator compares the ionization chamber voltage to a voltage derived from a resistor divider across VDD. This divider voltage is available externally on pin 13 (VSEN). When smoke is detected this voltage is internally increased by 130mV nominal to provide hysteresis and make the detector less sensitive to false triggering. Pin 13 (VSEN) can be used to modify the internal set point for the smoke comparator by using external resistors to VDD or VSS. Nominal values for the internal resistor divider are indicated on the block diagram. These internal resistor values can vary by up to 20% but the resistor matching will typically be <2% on any one device. A transmission switch on pin 13 isolates this pin during the low battery test so that the low battery set point will not be affected if external resistors are used to modify the smoke sensitivity set point. The guard amplifier and outputs are always active and will be within 50mV of the DETECT input to reduce surface leakage. The guard outputs also allow for measurement of the DETECT input without loading the ionization chamber. Low Battery Detection - An internal zener reference is compared to the voltage divided VDD supply. The battery can be checked under load via the LED low side driver output since low battery status is latched at the end of the 10mS LED pulse. Pin 3 (LBADJ) can be used to modify the low battery set point by placing a resistor to VDD or VSS. Note that the internal resistor string is common to both pin 3 and pin 13 so there will be some interaction between the two. Modification of the low battery set point may affect the smoke sensitivity setting. LED Pulse - The LED is pulsed on for 10.5mS every 40S in standby. In alarm the LED is pulsed on for 10.5mS every 1S. Testing - At power up all internal registers are reset. By holding pin 12 (OSCAP) low the internal power strobe is active. Functional testing can be accelerated by driving pin 12 with a 4kHZ square wave however the 10.5mS strobe period should be maintained for proper operation of the analog circuitry. Please refer to the timing diagrams. Horn Tone - Pin 4 selects the NFPA72 horn tone (high or floating) or the 2/3 duty cycle continuous tone (low).
Telephone 610.992.0727 Page 4 of 7
E-mail: rande@randeint.com DS-RE46C120-010907 This datasheet contains PROPRIETARY and CONFIDENTIAL information.
Facsimile 610.992.0734
RE46C120
CMOS Ionization Smoke Detector ASIC Product Specification R&E International
Typical Application
Figure 2
Notes: 1. 2. 3. 4. Float or connect pin 4 to VDD for NFPA72 horn pattern, connect to VSS for 2/3 duty cycle continuous tone R3, R4 and C1 are typical values and may be adjusted to maximize sound pressure. C2 should be located as close as possible to the device power pins. Route the pin 8 PC board trace away from pin 7 to avoid coupling.
Telephone 610.992.0727 Page 5 of 7
E-mail: rande@randeint.com DS-RE46C120-010907 This datasheet contains PROPRIETARY and CONFIDENTIAL information.
Facsimile 610.992.0734
RE46C120
CMOS Ionization Smoke Detector ASIC Product Specification R&E International
Timing Diagram
Standby Mode; No Low Battery; No Alarm Alarm No Low Battery ; Alarm Low Battery ; No Alarm Low Battery ;
Oscillator
Pin 15 > Pin 13 Pin 13 > Pin 15; 130m Level Shift on Pin 13 V Pin 15 > Pin 13
1.67S
10m S
Internal Clock
24 Clock Cycles (40 S) 24 Clock Cycles (1S)
LED DETCOMP (pin1) Sample (2/3 Duty) Sample (NFPA72)
THON3 THOF3
Low Battery Warning Chirp
Horn (2/3 Duty Cycle, TONE=VSS)
Low Battery Warning Chirp
Horn (NFPA72, TONE=Open or VDD)
See Figure Below for Com plete Tem poral Horn Cycle
Notes: 1. Smoke is not sampled when the horn is active so the horn cycle is self completing 2. Low battery warning chirp is suppressed in alarm
THON1 THOF1 THOF2
Complete Temporal Horn Pattern
Telephone 610.992.0727 Page 6 of 7
E-mail: rande@randeint.com DS-RE46C120-010907 This datasheet contains PROPRIETARY and CONFIDENTIAL information.
Facsimile 610.992.0734
RE46C120
CMOS Ionization Smoke Detector ASIC Product Specification R&E International
R&E INTERNATIONAL, Inc. reserves the right to make changes without further notice to any products herein to improve reliability, function or design. R&E INTERNATIONAL, Inc. does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights, nor the rights of others. R&E INTERNATIONAL, Inc. products are not authorized for use as critical components in life support devices or systems without the express written approval of the President of R&E INTERNATIONAL, Inc. Life support devices or systems are devices or systems which are intended for surgical implant into the body to support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
Telephone 610.992.0727 Page 7 of 7
E-mail: rande@randeint.com DS-RE46C120-010907 This datasheet contains PROPRIETARY and CONFIDENTIAL information.
Facsimile 610.992.0734

▲Up To Search▲

Price & Availability of RE46C120

	To Download RE46C120 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .